Page 103 - IJB-8-1

Zhou, et al.
Process Failure Analysis of Thin-Wall Structures Made by 36. Chen Y, Wen P, Voshage M, et al., 2019, Laser Additive
Laser Powder Bed Fusion Additive Manufacturing. J Mater Manufacturing of Zn Metal Parts for Biodegradable Implants:
Sci Technol, 98:233–43. Effect of Gas Flow on Evaporation and Formation Quality.
25. Espana FA, Balla VK, Bose S, et al., 2010, Design and J Laser Appl, 31:022304.
Fabrication of CoCrMo Alloy Based Novel Structures for 37. Meng B, Fu MW, Fu CM, et al., 2015, Multivariable Analysis
Load Bearing Implants Using Laser Engineered Net Shaping. of Micro Shearing Process Customized for Progressive
Mater Sci Eng C Mater Biol Appl, 30:50–7. Forming of Micro-Parts. Int J Mech Sci, 93:191–203.
https://doi.org/10.1016/j.msec.2009.08.006 https://doi.org/10.1016/j.ijmecsci.2015.01.017
26. Vignesh M, Kumar GR, Sathishkumar M, et al., 2021, 38. Bhatt NH, Pati AR, Kumar A, et al., 2017, High Mass Flux
Development of Biomedical Implants through Additive Spray Cooling with Additives of Low Specific Heat and
Manufacturing: A Review. J Mater Eng Perform, 30:4735–44. Surface Tension: A Novel Process to Enhance the Heat
https://doi.org/10.1007/s11665-021-05578-7 Removal Rate. Appl Therm Eng, 120:537–48.
27. Kok Y, Tan XP, Wang P, et al., 2018, Anisotropy and 39. Beals J, She Y, Jagdale V, et al., 2020, Structured Powder
Heterogeneity of Microstructure and Mechanical Properties Particles for Feedstock Improvement for Laser Based
in Metal Additive Manufacturing: A Critical Review. Mater Additive Manufacturing. Philadelphia, PA: MyScienceWork.
Des, 139:565–86. 40. Gu DD, Meiners W, Wissenbach K, et al., 2013, Laser
https://doi.org/10.1016/j.matdes.2017.11.021 Additive Manufacturing of Metallic Components: Materials,
28. Singh S, Ramakrishna S, Singh R, 2017, Material Issues Processes and Mechanisms. Int Mater Rev, 57:133–64.
in Additive Manufacturing: A Review. J Manuf Processes, 41. Sing SL, An J, Yeong WY, et al., 2016, Laser and Electron-
25:185–200. Beam Powder-Bed Additive Manufacturing of Metallic
https://doi.org/10.1016/j.jmapro.2016.11.006 Implants: A Review on Processes, Materials and Designs.
29. Hase T, Ohtagaki T, Yamaguchi M, et al., 2016, Effect of J Orthop Res, 34:369–85.
Aluminum or Zinc Solute Addition on Enhancing Impact 42. Brika SE, Letenneur M, Dion CA, et al., 2020, Influence of
Fracture Toughness in Mg-Ca Alloys. Acta Mater, 104:283–94. Particle Morphology and Size Distribution on the Powder
30. Strano G, Hao L, Everson RM, et al., 2013, A New Approach to Flowability and Laser Powder Bed Fusion Manufacturability
the Design and Optimisation of Support Structures in Additive of Ti-6Al-4V Alloy. Addit Manuf, 31:100929.
Manufacturing. Int J Adv Manuf Technol, 66:1247–54. https://doi.org/10.1016/j.addma.2019.100929
https://doi.org/10.1007/s00170-012-4403-x 43. Leitz, K., -H., et al., 2018, Fundamental Analysis of the
31. Montani M, Demir AG, Mostaed E, et al., 2017, Processability Influence of Powder Characteristics in Selective Laser
of Pure Zn and Pure Fe by SLM for Biodegradable Metallic Melting of molybdenum based on a multi-physical simulation
Implant Manufacturing. Rapid Prototyp J, 23:514–23. model. Int J Refract Met Hard Mater, 72:1–8.
https://doi.org/10.1108/rpj-08-2015-0100 44. Halada K, Minagawa K, Chiba K, et al., 2009, Solidified
32. Shuai C, Cheng Y, Yang Y, et al., 2019, Laser Additive Microstructure of Zn-Al Alloy Powders Produced by Various
Manufacturing of Zn-2Al Part for Bone Repair: Formability, Atomization Methods. J Jpn Soc Powder Powder Metallurgy,
Microstructure and Properties. J Alloys Compd, 798:606–15. 40:1160–5.
33. Yang Y, Yuan F, Gao C, et al., 2018, A Combined Strategy to 45. Tong L, Reddy RG, 2005, Synthesis of Titanium Carbide
Enhance the Properties of Zn by Laser Rapid Solidification Nano-Powders by Thermal Plasma. Scr Mater, 52:1253–8.
and Laser Alloying. J Mech Behav Biomed Mater, 82:51–60. 46. Ruvalcaba BE, Arrieta E, Escarcegaa AH, et al.,
34. Wen P, Jauer L, Voshage M, et al., 2018, Densification Manufacturing Process and Parameters Development for
Behavior of Pure Zn Metal Parts Produced by Selective Laser Water-atomized Zinc Powder for Selective Laser Melting
Melting for Manufacturing Biodegradable Implants. J Mater Fabrication. United States: The University of Texas at Austin.
Process Technol, 258:128–37. 47. Sungkhaphaitoon P, Plookphol T, Wisutmethangoon S, 2012,
https://doi.org/10.1016/j.jmatprotec.2018.03.007 Design and Development of a Centrifugal Atomizer for
35. Qin Y, Wen P, Guo H, et al., 2019, Additive Manufacturing Producing Zinc Metal Powder. Int J Appl Phys Math, 2:77.
of Biodegradable Metals: Current Research Status and Future 48. Wen P, Voshage M, Jauer L, et al., 2018, Laser Additive
Perspectives. Acta Biomat, 98:3–22. Manufacturing of Zn Metal Parts for Biodegradable
https://doi.org/10.1016/j.actbio.2019.04.046 Applications: Processing, Formation Quality and Mechanical

International Journal of Bioprinting (2022)–Volume 8, Issue 1 89