Page 64 - IJB-6-2

Effects of topology optimization in multimaterial 3D bioprinting of soft actuators
Dissertations. A 115-line MATLAB Implementation. Struct Multidiscip
25. Schumacher A, 2013, Mathematische Grundlagen der Optim, 49:621–42. DOI: 10.1007/s00158-013-0999-1.
Optimierung, in Optimierung mechanischer Strukturen. Springer, 36. Zhang H, Wang Y, Cao J, et al., 2018, Topology Optimized
Berlin. pp. 45–55. DOI: 10.1007/978-3-642-34700-9_3. Design, Fabrication and Evaluation of a Multimaterial Soft
26. Harzheim L, 2016, Der Natur in die karten geschaut Gripper. In: 2018 IEEE International Conference on Soft
optimierungsverfahren aus dem bereich der bionik. In: Robotics (RoboSoft). DOI: 10.1109/robosoft.2018.8405363.
Karosseriebautage Hamburg. Springer, Berlin. pp. 3–16. 37. Lee JM, Yeong WY, 2016, Design and Printing Strategies in
DOI: 10.1007/978-3-658-14144-8_1. 3D Bioprinting of Cell-Hydrogels: A Review. Adv Healthc
27. Huang X, Xie M, 2010, Evolutionary Topology Optimization Mater, 5:2856–65. DOI: 10.1002/adhm.201600435.
of Continuum Structures: Methods and Applications. John 38. Wu Q, Maire M, Lerouge S, et al., 2016, Solvent-cast 3D
Wiley & Sons, New York. Printing of Chitosan Hydrogel Scaffolds for Guided Cell
28. Zhang H, Kumar AS, Chen F, et al., 2019, Topology Optimized Growth. Front. Bioeng. Biotechnol. Conference Abstract:
Multimaterial Soft Fingers for Applications on Grippers, 10 World Biomaterials Congress. DOI: 10.3389/conf.
th
Rehabilitation, and Artificial Hands. J IEEE/ASME Trans FBIOE.2016.01.00336.
Mechatron, 24:120–31. DOI: 10.1109/tmech.2018.2874067. 39. Zhang J, Allardyce BJ, Rajkhowa R, et al., 2018, 3D Printing
29. He D, Liu SJ, 2008, BESO Method for Topology Optimization of Silk Particle-reinforced Chitosan Hydrogel Structures and
of Structures with High Efficiency of Heat Dissipation. their Properties. ACS Biomater Sci Eng, 4:3036–46. DOI:
Int J Simul Multidiscip Des Optim, 2:43–8. DOI: 10.1051/ 10.1021/acsbiomaterials.8b00804.
smdo:2008005. 40. Zolfagharian A, Kouzani AZ, Khoo SY, et al., 2018, 3D
30. Kim MG, Kim JH, Cho SH, 2010, Topology Design Printed Soft Parallel Actuator. J Smart Mater Struct,
Optimization of Heat Conduction Problems Using Adjoint 27:45019. DOI: 10.1088/1361-665x/aaab29.
Sensitivity Analysis Method. Adv Mech Eng, 23:683–91. 41. Bouguet JY, 2010, Camera Calibration Toolbox for Matlab.
31. Gersborg-Hansen A, Bendsøe MP, Sigmund O, 2005, International Conference on Indoor Positioning and Indoor
Topology Optimization Using the Finite Volume Method. Navigation.
Struct Multidiscipl Optim, 50:523–35. DOI: 10.1007/s00158- 42. Choong YY, Maleksaeedi S, Eng H, et al., 2017, 4D Printing
005-0584-3. of High Performance Shape Memory Polymer Using
32. Kaup IA, 2018, Rekonstruktion Verrauschter Nichtregelmäßig Stereolithography. Mater Des, 126:219–25. DOI: 10.1016/j.
Abgetasteter Bilddaten. Bachelor Thesis. matdes.2017.04.049.
33. Svanberg K, 1987, The Method of Moving Asymptotes a 43. Donnan FG, 1924, The Theory of Membrane Equilibria.
New Method for Structural Optimization. 24:359–73. Chem Rev, 1:73–90.
34. Wiedemann J, 2007, Leichtbau: Elemente und Konstruktion. 44. Zolfagharian A, Kouzani AZ, Khoo SY, et al., 2017,
Springer-Verlag, Berlin. Development and Analysis of a 3D Printed Hydrogel Soft
35. Tavakoli R, Mohseni SM, 2014, Alternating Active-phase Actuator. J Sen Actuators A Physical, 265:94–101. DOI:
Algorithm for Multimaterial Topology Optimization Problems: 10.1016/j.sna.2017.08.038.

60 International Journal of Bioprinting (2020)–Volume 6, Issue 2